Skip to the page

Guide ยท Modesto

Furnace heating repair near me

If the heat is out and the house is getting cold, the order of your next steps matters more than the cause. This page covers the first hour, how to find fast local help and what a rush call costs.

Two columns: what a homeowner can check, and what to leave to a pro.

Furnace heating repair near you means a local HVAC specialist who can come to the house, find why the gas furnace is not producing heat and fix it. If the heat is out, spend the first few minutes on safety and quick checks, then request quotes from nearby businesses and ask who can attend today.

This page is about speed and sequence: what to do before help arrives, what 24-hour service really involves and what a rush call costs. For the full picture of repair and replacement, read the furnace repair and replacement guide. For symptom-by-symptom diagnosis, see furnace repair and service.

What should you do in the first hour with no heat?

Check the thermostat, the filter and the power, and make sure nobody is at risk from the cold or from carbon monoxide. Those steps are quick, sometimes solve the problem and give any technician a better starting point. Then request quotes and write down what you saw.

A sensible order:

  1. Safety first. If a carbon monoxide alarm is sounding, leave the house, call 911 and wait for responders. Do not hunt for the cause (CPSC).
  2. Thermostat. Heat mode, set several degrees above the room, fresh batteries.
  3. Power. The breaker, and the on-off switch on or near the furnace.
  4. Filter. If it is clogged, replace it.
  5. Look at the furnace without opening it: is there an error code flashing on the small window or light? Note the pattern.
  6. Call or request quotes, and say you have no heat.

Do not light the pilot, reset a gas valve or open the burner compartment. Gas and combustion work is for a pro.

Is 24-hour heating repair available near Modesto?

Some local HVAC businesses take emergency calls outside normal hours, but no site can promise a specific response time, and availability changes during the first cold snaps when many homes lose heat at once. Ask each business directly whether they can attend tonight, how soon, and what the after-hours charge is.

When you request quotes through the price request form, say it is a no-heat situation and the time you need someone. Quotes come from independent local businesses, so each will tell you its own hours and surcharge. Compare them on:

  • Earliest arrival, in writing if possible.
  • Surcharge for nights, weekends or holidays.
  • Diagnostic fee, and whether it is credited toward the repair.
  • Whether the person who comes can complete common repairs on the first visit.

Coverage depends on each business, so check that your town is in its service area when you request quotes. See the full list of local areas, or start from the HVAC repair quotes home page. The furnace emergency repair page goes deeper on same-day calls.

How much does an emergency furnace call cost?

Businesses often add a surcharge for after-hours calls. Fixr's AC repair guide (January 2026) lists emergency rates of $150 to $300 per hour, or two to three times normal. These are national figures, not Modesto prices, and the repair itself comes on top of the visit fee.

A furnace closet door in a hallway
Cost itemPublished rangeSource
Emergency rates$150 to $300 per hour, or two to three times normalFixr AC repair guide
Diagnostic or service call$75 to $250Fixr guides
Typical furnace repair$349 to $650Fixr furnace repair guide

If the problem can safely wait until morning, you may save the surcharge. A house that is cold but not dangerously so, with working space heating elsewhere, might wait. A home with a baby, an elderly person or someone ill should not. See the emergency HVAC service cost guide for more on what drives the premium.

What do furnace heating repairs usually cost?

Fixr's furnace repair guide (updated August 2025) lists a typical range of $349 to $650, with parts from $66 up to $2,673 for the expensive ones. Cheap fixes include an igniter or flame sensor; expensive ones include a heat exchanger or control board.

Common repairs, from the Fixr furnace repair guide:

  • Igniter: $96 to $178 with the service call
  • Flame sensor: $68 to $127 with the service call
  • Limit switch: $66 to $122
  • Control board: $390 to $725
  • Blower: $562 to $1,045
  • Heat exchanger: $1,346 to $2,673

The usual labor rate is $87 to $162 per hour. Parts that cost the least often cost the same in labor and call fees, which is why a repair that sounds trivial still lands at $100 or more. If the furnace is old and the quote is large, compare it with the furnace replacement cost before you approve. A new furnace installed runs a typical $2,800 to $7,500 nationally, per the Fixr new furnace guide.

Which furnace problems can cut your heat but are quick fixes?

Several quick fixes are low-cost: a dirty filter, a thermostat setting, a flame sensor that needs cleaning or a clogged condensate drain line on a high-efficiency furnace, which can stop the system until it clears. A technician can handle these in one visit, often without ordering parts.

A gas furnace follows a fixed sequence: the draft inducer starts, the pressure switch proves airflow, the igniter heats, the gas valve opens, the flame is sensed and the blower starts. A fault at any stage stops the rest. That is why a small part can leave the house cold and also why the repair is usually small.

High-efficiency furnaces make water as part of burning gas, and a blocked condensate trap or drain can keep the pressure switch from closing. Industry troubleshooting guides describe this, and it is a common reason newer furnaces stop. Most furnaces lock out after a few failed ignition tries and flash a code; check the manual for the count, and write the code down.

Higher energy bills, odd noises and rooms that never get warm are signs of a furnace that is struggling, not just stopped. Mention them on the call.

Questions people ask

How long does furnace heating repair take?

A simple repair such as an igniter, flame sensor or filter-related fault can finish in a single visit, once the technician has diagnosed it. Parts that are not on the truck, such as a control board for an uncommon model, can push completion to the next day. Ask for an estimate when you book.

What should I ask before I hire someone for furnace heating repair?

Ask for the earliest arrival time, the diagnostic fee and whether it is credited, any after-hours surcharge and a written quote before work starts. Check the business on the CSLB license check at cslb.ca.gov. California requires a CSLB license for HVAC work of $1,000 or more in labor and materials.

Do I need to be home for furnace heating repair?

Yes, for at least the start. Someone has to let the technician in, show where the furnace and thermostat are, and approve the price. A gas furnace repair should not be left half-done in an empty house, so ask the business what they will leave running when they go.

Can I use a space heater while I wait?

CPSC's winter safety warnings cover generators, furnaces and space heaters, and note that more than half of carbon monoxide deaths occur in November to February. Fuel-burning heaters indoors are the risk. If you use any heater, follow its instructions, keep it clear of fabric and keep working CO alarms on every level. Never use a generator or fuel-burning heater inside.

Does a furnace tune-up prevent no-heat calls?

CPSC urges a professional inspection of furnaces and other fuel-burning heating systems every year. A visit can catch worn parts before the cold arrives. See the HVAC service plan page for what a tune-up includes and what plans cost.

Sources

Last updated